Rational CombiMaster CM Bedienungsanleitung Seite 76
- Seite / 186
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
-76-
S
S
C
C
Calibration SCC
Step
1
10
In case of „13“ check:
20
(min: 4x20sec;
max: 4x180sec)
In case of „20“ check:
30
(4x 30 sec)
In case of „50“ check:
40
(max. 800 sec)
In case of „11“ check:
50
(40 sec)
Unit status:
Basic conditions o.k?:
Continue with step 10
Measurement:
Offset Diff. pressure sensor P1
• Heating: OFF
• Motor: OFF
• Humidity fl ap: Closed
P1 or 12V power supply to P1
Controlling with all 4 fan speeds:
Steady signal of rpm and pressure
• Heating: OFF
• Motor: ON
• Humidity fl ap: Closed
In diagnostic mode: P1, B4, rpm
Measuring at all 4 fan speeds:
Calibration value: cold cabinet
• Heating: OFF
• Motor: ON
• Humidity fl ap: Closed
Überprüfung im Diagnoseprogramm: P1, B4, rpm
Step 20 and 30 will run 1x for each rpm setting!
Filling cabinet with steam until B2 sensor reaches
80°C (176°F)
• Heating: ON
• Motor: OFF
• Humidity fl ap: Closed
Steam heating elements, SSR, quenching sensor
Stand-by in steam saturation
• Heating: ON
• Motor: ON (lowest speed)
• Humidity fl ap: Closed
Error code
71
13
20
71
50
11
71
none
Reason:
Basic conditions not
met
Offset out of range
Value out of allo-
wable range
Max time of
4x180sec exceded
Calibration value not
in expected range
(logic)
No steam heating
Max time of
4x800sec exceeded
Calibration at the customers site must be done under the following conditions:
Changing the pcb, extrenal EEPROM, B4 humidity sensor, Pressure sensor P1, replacing the
air baffl e or divider plate between the 2 fan motors of a fl oor model, fan motor, detaching of the fan wheel and
installation of the appliance above 1000m (3000ft) above sea level or below sea level (dead sea).
Basic condition Cabinet sensor B1 Quench. sensor Humidity sensor
Temperatures: B1 <40°C B2 <45°C B4 < 40°C
Basic condition Heating: OFF Fan motor: OFF Humidity fl ap: Closed
Hardware: Side panel must be fi tted; Unit must be clean, but may be wet
In order to achieve the best possible calibration values, insert
2 GN-container 20 or 40 mm deep with the opening facing downwards
in 61 and 62 units into rail 2 and 5
in 101 and 102 units into rail 3 and 7
in 201 and 202 units 3 GN container into rail 3, 10 and 17
- Training Manual 1
- Training Manual 2
- CM Technique from 04 - 2004 4
- B1 - 100°C(212°F) 7
- Key code CM from 04 - 2004 8
- 42.00.004 10
- 42.00.047 10
- Motor for CM 40.00.274 11
- Failure Codes CM from 04-2004 25
- CM Gas from 04 - 2004 26
- Ignition box 27
- Checking CO 31
- How to carry 33
- SCC Control Panel 35
- Duration 37
- CleanJet 39
- 10/22/06 39
- A2 SCC pcb 44
- A3 Add On pcb 44
- 11,5 V AC 45
- Motor for SCC / CM 46
- SCC Units: Sequence of Events 48
- Service level SCC 54
- SCC Diagnostic Mode overview 56
- SCC Diagnostic Mode 57
- SCC Running Times overview 60
- SCC Running Times 61
- Overview Basic Settings 64
- Overview Function test 68
- Function test 69
- (CDS sensor) 73
- Micro switch ClimaPlus) 73
- Service messages SCC 74
- Value out of allo 76
- Calibration SCC 77
- Control Drain Valve 54.00.357 78
- SCC Gas from 04-2004 80
- Gas Steam Bower 84
- SCC Gas from 04 - 2004 85
- 14 - Function Test 86
- Gas Steam Blower Start/Stop 86
- CO2 FC xxx 86
- Flash SCC Software 90
- Transformer 95
- How to update CM units via PC 97
- Warning! 98
- Caution: 98
- Descaling interrupt SCC: 99
- Descaling interrupt CM: 99
- CHECKLIST SCC / CM 100
- PERIMETER CLEARANCES 101
- Water connection YES NO 101
- Yes NO 103
- YES NO 103
- Preventive Maintenance SCC/CM 104
- Preventative Maintenance SCC 105
- Inspections List 106
- Water info 108
- Service 10 111
- Service 11 112
- Service 25 113
- Service 26 114
- Service 27 114
- Service 34 115
- Fault List SCC 116
- Fault List CM 122
- 76-00011 131
- Überblick CM101E 131
- 3NAC400V 50-60Hz 131
- Hot air heating/Steam heating 133
- MODUL 3 Klima Plus, Fühler 134
- Humidity control, Sensors 134
- MODUL 4 Wasser 135
- Water, Drain, CleanJet 135
- MODUL 5 Lüftermotor 136
- Fan Motor, Cooling Fan 136
- MODUL 6 Summer, EEPROM 137
- Buzzer, EEPROM 137
- MODUL 7 Option 138
- Positionsliste 139
- Bill of material 139
- 76-00017 140
- MODUL 5 Lüfter motor 141
- F an Motor, C ooling Fan 141
- 3NAC 400V 50- 60H z 141
- INDEX F 142
- 76-00050 144
- Überblick CM 101/102 G 144
- 1NAC230V 50-60Hz 144
- CM 101/102 G 145
- 0Version 146
- 0Ve rsion 153
- 76-00054 154
- C M 201/202 G 154
- 1NAC 230V 50- 60H z 154
- 76-00003 163
- 76-00016 168
- S C C 202E 169
- 76-00006 176
- SCC 101/102 G 176
- 76-00051 182
- S C C 201/202 G 182
- Startzeit 184
- CM Service Reference 185
- 80.51.033 186
Verwandte Produkte und Handbücher für Kleine Küchengeräte Rational CombiMaster CM
(84 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 1.892 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern